Is there a later firmeware that resolves the issue? I thought I checked and found the one on the switch to be the latest available already, but I might have missed something there. Not happy about this, as we just bought the switches in order to realize some sort of LAG / port trunking backbone between two office parts. Using only one or even better no link resolves the issue. Tried both static LAG and LACP but they lead to the same result, which is LEDs rapidly blinking upon plugging in the 2nd link, CPU going from ~10% to ~40% and web interface starting to become slower and slower to the point that it's not usable any longer (impossible to log in, if not already logged in while connecting 2nd link).
#Lag switch v2 not working mac#
Using "SRC MAC + DST MAC" hash algorithm, VLAN ID 1 on all ports and the LAG (i.e. Seeing the same issue when trying to connect two T1600G-28TS (UN, v3.0) together using a 2-link LAG.įirmware is "3.0.0 Build 20180130 Rel. I remember that we need to enable admin status for VLAN interface. If you mean that you cannot access the secondary switch thorugh the primary switch, please make sure that the interface of vlan 512 is up and you can see the related routing entry on routing table. The lot of ARP query is blinking the leds, but no ARP reply. The packet capture show a thing: No ARP reply from switches. I can't reach the secondary switch, trough, the primary switch. The switches last 2 ports in the lag (23-24 to 47-48)ĪND i set up port 1 untagged 512 and pvid 512. I set up the last 2 ports on switches AND lag untagged 512 vlan THEN i set the last 2 ports on swithes AND the LAG PVID to 512. If the ports other vlan (an unused techical) = not vorking. I set the lag untagged vlan, lag port primary vlan, the included ports untagged vlan AND primary vlan. Before write here, i read lot of post of this forum and other sites.
Thank you the answer, but the lag is configured. I managed over 400 Enterprise switch without problem. I programmed lot of Switch and until V3.0 this method working always on HP, 3COM, and TP-Link switches. I disconnect LAG, then the 512 vlan interface is accessible again. CPU utilization 40% Traffic 0% in log: NOTHING Vlan 512 inaccessible No ping no webpage.
Not slow, SLOOOOOOW!, and the LAG has no ports. I connect to switch 28 port 2 (system vlan default ip) The web page slow. The web page slowing, the LAG has only onle link (24). And the port 1 in switch 28 (this port used to connect the switch now). On the Switch's LAG's lower port (24) and (43) blinking FAST.
After 5~10 Seconds, the LEDs on the switch start blinking like a madness. The switch realize and communicate on the webpage, the 23-24 ports on active LAG. I connect to switch's (28) on ip 10.32.0.189 (vlan 512 port 1) web config. Port 43-44 Active LAG (LACP) in untagged vlan 512 PVID 512 other vlans on tagged (481.482.483,484,485,486,487,488,489,490,491) on this ports (43-44 and LAG only) All other ports untagged 482, Except port 2 is vlan 1 for config, and port 1 in untagged 512 for config in future. Port 23-24 Active LAG (LACP) in untagged vlan 512 PVID 512 other vlans on tagged (481.482.483,484,485,486,487,488,489,490,491) on this ports (23-24 and LAG) only All other ports untagged 481, Except port 2 is vlan 1 for config, and port 1 in untagged 512 for config in future. The 28PS is named below "28" the 52TS named below "52". I configured lot of switches and i don't understand why not working on JetStream v3.0. Indifferent wich type of switch th other.
If i create a LACP LAG in TP-Link V3 Switch, working only a few minutes, then drop one or more or all ports. We have LOT of problems with Ver 3.0 Jetstream Switches Until now we change them to V2.x Switches.